Other listings by this author |
|
 MITCalc Internal Spur Gear Calculation 1.21 (Downloads: 1271)
Geometric design and strength check of internal spur gear (straight and helical) Geometric design and strength check of internal spur gear with straight and helical toothing. Application is developed in MS Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Calculation of helical and straight toothing.
- Automatic design of a transmission with the minimum number of input requirements.
- Design for entered coefficients of safety (static, dynamic).
- Calculation of compl...
|
|
 MITCalc Shells 1.13 (Downloads: 1048)
Shells - Deformation and stress of rotational shells The calculation concerns solutions of pressure vessels and their components. The calculation solves deformations and curves of stress in rotational shells loaded with axial force, pressure, radial force and a bending moment. This program is intended for homogeneous shells of identical thickness and a single material. The calculation also enables solutions for connecting two shells of different parameters (thickness, material, dimensions...).
The program enable...
|
|
 MITCalc Slender strut buckling 1.20 (Downloads: 1337)
Calculation of the slender strut (column) buckling The program is designed to calculate the optimum cross-section and perform strength check of slender struts strained for buckling. The program includes:
- Selection of six basic types of buckling.
- Calculation of area characteristics of 20 types of cross-sections.
- Design of optimum profile accommodating the set load.
- Strength check of the strut.
- Calculation and graphical representation of permitted stress dependent on slende...
|
|
 MITCalc Tolerance analysis 1.19 (Downloads: 1227)
Tolerance analysis of linear, 2D and 3D dimensional chains Two programs for the tolerance analysis of linear, 2D and 3D dimensional chains
1) Tolerance analysis of linear dimensional chains.
The program is designed for tolerance analysis of linear (1D) dimensional chains. The program solves the following
problems:
- Tolerance analysis, synthesis and optimization of a dimensional chain using the arithmetic "WC" (Worst case) method, possibly the statistical "RSS" (Root Sum Square...
|
|
 MITCalc Compression Springs 1.22 (Downloads: 1462)
Geometric and strength designs of helical compression cylindrical springs The calculation is intended for the purposes of geometric and strength designs of helical compression cylindrical springs made of wires and rods of circular sections, loaded with static or fatigue loading. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Automatic design of a spring.
- Selection of an optimal alternative of spring design in view of strength, geometry and we...
|
|
 MITCalc Torsion Springs 1.22 (Downloads: 1452)
Geometric and strength designs of spiral cylindrical torsion springs The calculation is intended for the purposes of geometric and strength designs of spiral cylindrical torsion springs made of wires and rods in circular sections, cold formed, loaded with a static or cyclic loading. Application is developed in MS Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Automatic design of the spring.
- Selection of the optimal design of the spring with respect to strength, geo...
|
|
 MITCalc Gear rack design 1.11 (Downloads: 996)
Geometric design and strength check of gear rack (straight and helical) Geometric design and strength check of gear rack with straight and helical toothing. Application is developed in MS
Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Calculation of helical and straight toothing.
- Automatic design of a transmission with the minimum number of input requirements.
- Design for entered coefficients of safety (static, dynamic).
- Calculation of complet...
|
|
 MITCalc Roller Chains Calculation 1.21 (Downloads: 1271)
Design and strength check of roller chain transmission The calculation is designed for a geometrical design and strength check of common chain transmissions using roller
chains. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the
following tasks:
- Selection of a power suitable type of chain.
- Selection of an optimum transmission alternative regarding power, geometry and weight.
- Calculation of geometric, strength, safety and oper...
|
|
 MITCalc Pinned couplings 1.19 (Downloads: 1674)
Geometric design and strength check of couplings using pins and clevis pins The calculation is intended for the geometric design and strength check of couplings using pins and clevis pins. The program is used to solve the following tasks:
- Design of pin for spring attachment.
- Design of couplings with securing pins.
- Design of cross pin in rod and sleeve.
- Design of radial pin for shaft-hub connection.
- Design of longitudinal pin for shaft-hub connection.
- Design of clevis pin for rotating rod-clev...
|
|
 MITCalc Rolling Bearings Calculation I 1.20 (Downloads: 1356)
Selection, calculation and check of rolling bearings SKF This module can be used for the selection, calculation and check of rolling bearings of the company SKF. The programme provides solutions to the following tasks:
- Selection and check of a suitable bearing. The document includes a database of approx. 10,000 different rolling bearings SKF in all basic types and design.
- Calculation of basic bearing parameters (life, static safety, etc.).
- Calculation of adjusted bearing life acc. to the new met...
|
|
 MITCalc Force shaft connection 1.20 (Downloads: 1047)
Designs and strength checks of force couplings of shafts with hubs The calculation is intended for geometrical design and strength check of force couplings of shafts with hubs with a cylindrical contact area (Interference fit, clamping connection). The application provides solutions for the following tasks:
- Design of force fits, possibly shrink fits.
- Design of clamping connections with separated, or one-side cut hub.
- Strength check of designed couplings.
- Check of interference fit strained by addi...
|
|
 MITCalc Tolerances 1.20 (Downloads: 1279)
Tolerances, deviations and fits of machine parts This calculation includes tables and calculations for easy option of fits of machine parts and determination of their dimensional tolerances and deviations. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Selection of suitable fits of machine parts according to the international standard ISO 286.
- Determination of dimensional tolerances and deviations of machine parts ac...
|
|
 MITCalc Plates design and calculation 1.15 (Downloads: 1300)
Deflection, stress and variation of forces in the loaded flat plates This calculation deals with the deflection, stress and variation of forces in the loaded flat plates. The calculation is designed for plates that are flat, homogeneous, with the same thickness and made from one material. The plates may be circular, annular circular and rectangular. The plates may be loaded evenly (unevenly) on the whole surface (or its part) or they may be loaded by the force distributed on the circle. The programme enables:
- Selection from c...
|
|
 MITCalc3D for Solid Edge 1.61 (Downloads: 459)
Mechanical, Industrial and Technical Calculations for Solid Edge MITCalc is a multi-language set of mechanical, industrial and technical calculations for the day-to-day routines. It will
reliably, precisely, and most of all quickly guide customer through the design of components, the solution of a
technical problem, or a calculation of an engineering point without any significant need for expert knowledge.
MITCalc contains both design and check calculations of many common tasks, such as: spur and bevel gear, b...
|
|
 MITCalc Timing Belts Calculation 1.21 (Downloads: 1287)
Geometric design and strength check of timing belt transmission The calculation is designed for a geometrical design and strength check of toothed belt transmissions. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Selection of the type of belt with a suitable output power.
- Selection of an optimum transmission alternative in view of power, geometry and weight.
- Option of designing a non-standard transmission.
- Calcul...
|
|
 MITCalc Spur Gear Calculation 1.24 (Downloads: 1250)
Geometric design and strength check of spur gear (straight and helical) Geometric design and strength check of spur gear with straight and helical toothing. Application is developed in MS
Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Calculation of helical and straight toothing.
- Automatic design of a transmission with the minimum number of input requirements.
- Design for entered coefficients of safety (static, dynamic).
- Calculation of complet...
|
|
 MITCalc V-Belts Calculation 1.22 (Downloads: 1255)
Geometric design and strength check of V-belt transmission The calculation is designed for a geometrical design and strength check of belt transmissions using V-belts. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Calculation for 2 or 3 pulleys.
- Automatic design of a transmission with the minimum of input requirements.
- Design and calculation of geometrical parameters (diameters of pulleys, axis distances, length of the...
|
TradeTrakker 2.93: Powerful investment tracking program to automatically track stocks/mutual funds
JaSFtp 11.10: JaSFtp - Automated SFTP client (secure FTP), Run 1000+ tasks on a schedule.