Other listings by this author |
|
 MITCalc Shafts Calculation 1.24 (Downloads: 1239)
Geometrical design and complex strength check of shafts The calculation is designed for geometrical design and complex strength check of shafts.
Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following
main tasks:
- Simple definition of installed shafts, including hollow ones.
- Options of definitions of necking-down, recesses, grooves and calculation of the relevant coefficients of stress concentration.
- Simple definition of s...
|
|
 MITCalc Worm Gear Calculation 1.18 (Downloads: 1310)
Geometric design and strength check of worm gear Geometric design and strength check of worm gear. Application is developed in MS Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Calculation of gearing dimensions.
- Automatic transmission design with minimum input requirements.
- Design for safety coefficients entered.
- Calculation of a table of proper solutions.
- Calculation of complete geometrical parameters.
- Calcu...
|
|
 MITCalc Roller Chains Calculation 1.21 (Downloads: 1251)
Design and strength check of roller chain transmission The calculation is designed for a geometrical design and strength check of common chain transmissions using roller
chains. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the
following tasks:
- Selection of a power suitable type of chain.
- Selection of an optimum transmission alternative regarding power, geometry and weight.
- Calculation of geometric, strength, safety and oper...
|
|
 MITCalc3D for Autodesk Inventor 1.61 (Downloads: 406)
Mechanical, Industrial and Technical Calculations for Autodesk Inventor MITCalc is a multi-language set of mechanical, industrial and technical calculations for the day-to-day routines. It will
reliably, precisely, and most of all quickly guide customer through the design of components, the solution of a
technical problem, or a calculation of an engineering point without any significant need for expert knowledge.
MITCalc contains both design and check calculations of many common tasks, such as: spur and bevel gear, b...
|
|
 MITCalc Pinned couplings 1.19 (Downloads: 1652)
Geometric design and strength check of couplings using pins and clevis pins The calculation is intended for the geometric design and strength check of couplings using pins and clevis pins. The program is used to solve the following tasks:
- Design of pin for spring attachment.
- Design of couplings with securing pins.
- Design of cross pin in rod and sleeve.
- Design of radial pin for shaft-hub connection.
- Design of longitudinal pin for shaft-hub connection.
- Design of clevis pin for rotating rod-clev...
|
|
 MITCalc Plates design and calculation 1.15 (Downloads: 1278)
Deflection, stress and variation of forces in the loaded flat plates This calculation deals with the deflection, stress and variation of forces in the loaded flat plates. The calculation is designed for plates that are flat, homogeneous, with the same thickness and made from one material. The plates may be circular, annular circular and rectangular. The plates may be loaded evenly (unevenly) on the whole surface (or its part) or they may be loaded by the force distributed on the circle. The programme enables:
- Selection from c...
|
|
 MITCalc Profiles Calculation 1.20 (Downloads: 1311)
Area characteristic of profiles and mass characteristic of solids The calculation solves area characteristics of profiles created in a simple graphic editor and mass characteristics of solids created by extrusion or rotation of the profile. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following tasks:
- Creation of a profile in a simple graphic editor.
- Calculation of area characteristics (Ix, Sx) for main axes passing through the centre of gravity.
...
|
|
 MITCalc Rolling Bearings Calculation I 1.20 (Downloads: 1332)
Selection, calculation and check of rolling bearings SKF This module can be used for the selection, calculation and check of rolling bearings of the company SKF. The programme provides solutions to the following tasks:
- Selection and check of a suitable bearing. The document includes a database of approx. 10,000 different rolling bearings SKF in all basic types and design.
- Calculation of basic bearing parameters (life, static safety, etc.).
- Calculation of adjusted bearing life acc. to the new met...
|
|
 MITCalc Tolerance analysis 1.19 (Downloads: 1209)
Tolerance analysis of linear, 2D and 3D dimensional chains Two programs for the tolerance analysis of linear, 2D and 3D dimensional chains
1) Tolerance analysis of linear dimensional chains.
The program is designed for tolerance analysis of linear (1D) dimensional chains. The program solves the following
problems:
- Tolerance analysis, synthesis and optimization of a dimensional chain using the arithmetic "WC" (Worst case) method, possibly the statistical "RSS" (Root Sum Square...
|
|
 MITCalc Timing Belts Calculation 1.21 (Downloads: 1263)
Geometric design and strength check of timing belt transmission The calculation is designed for a geometrical design and strength check of toothed belt transmissions. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Selection of the type of belt with a suitable output power.
- Selection of an optimum transmission alternative in view of power, geometry and weight.
- Option of designing a non-standard transmission.
- Calcul...
|
|
 MITCalc Shells 1.13 (Downloads: 1029)
Shells - Deformation and stress of rotational shells The calculation concerns solutions of pressure vessels and their components. The calculation solves deformations and curves of stress in rotational shells loaded with axial force, pressure, radial force and a bending moment. This program is intended for homogeneous shells of identical thickness and a single material. The calculation also enables solutions for connecting two shells of different parameters (thickness, material, dimensions...).
The program enable...
|
|
 MITCalc Compression Springs 1.22 (Downloads: 1441)
Geometric and strength designs of helical compression cylindrical springs The calculation is intended for the purposes of geometric and strength designs of helical compression cylindrical springs made of wires and rods of circular sections, loaded with static or fatigue loading. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Automatic design of a spring.
- Selection of an optimal alternative of spring design in view of strength, geometry and we...
|
|
 MITCalc Planet Gear Calculation 1.17 (Downloads: 1202)
Geometric design and strength check of planet gear (straight and helical) Geometric design and strength check of planetary gearing with straight and helical toothing. Application is developed in MS
Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Calculation of helical and straight toothing.
- Automatic design of a transmission with the minimum number of input requirements.
- Design for entered coefficients of safety (static, dynamic).
- Calculation of...
|
|
 MITCalc Bevel Gear Calculation 1.20 (Downloads: 1293)
Geometric design and strength check of bevel gear (straight, helical and curved) Geometric design and strength check of bevel gear with with straight, helical and curved toothing. Application is developed in MS Excel, is multi-language and supports Imperial and Metric units and solves the following main tasks:
- Calculation of straight, helical and curved toothing.
- Automatic design of a transmission with the minimum number of input requirements.
- Design for entered coefficients of safety (static, dynamic).
- Calcula...
|
|
 MITCalc Bolted connection 1.25 (Downloads: 1401)
Design and strength check of a prestressed bolt connection The calculation is designed for a geometrical design and strength check of a prestressed bolt connection, loaded by static or cyclic loading resp., acting both in the axis of the bolt and in the plane of the connected parts. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Automatic design of a connection bolt of standard design.
- Calculation and check of connections fitte...
|
|
 MITCalc Tolerances 1.20 (Downloads: 1260)
Tolerances, deviations and fits of machine parts This calculation includes tables and calculations for easy option of fits of machine parts and determination of their dimensional tolerances and deviations. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Selection of suitable fits of machine parts according to the international standard ISO 286.
- Determination of dimensional tolerances and deviations of machine parts ac...
|
|
 MITCalc V-Belts Calculation 1.22 (Downloads: 1236)
Geometric design and strength check of V-belt transmission The calculation is designed for a geometrical design and strength check of belt transmissions using V-belts. Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following main tasks:
- Calculation for 2 or 3 pulleys.
- Automatic design of a transmission with the minimum of input requirements.
- Design and calculation of geometrical parameters (diameters of pulleys, axis distances, length of the...
|
Advanced XLS Converter 2.55: With XLS Converter you can convert Excel (XLS) files into dozens of formats!